Recommended PCB Patterns
Headers
Low Temperature Plastic Insulator
glass filled nylon or
polyester, UL 94 VO
temp range -65o to + 125o C
insulation resistance 5000 megohm @ 500 VDC
RoHS Compliant
Color - black
High Temperature Plastic Insulator
Hi-temp Stanyl thermoplastic UL 94VO
Temp Range -65o to + 260o C
Heat Deflection: 260o C @ 264 psi
Insulation Resistance 5000 MEG OHM @ 500 VDC
Color - black
Terminal : (Both .025 sq and .020 dia)
Material - Phosphor Bronze, drawn wire, burr free both ends.
Current Rating - 3 amp continuous @ 100 VDC/Contact. - .025 sq.
- 2 amp continuous @ 100 VDC/Contact. - .020 dia.
TOLERANCES - unless otherwise noted on a specific part,
the following
tolerances apply to all parts.
| Straight Headers |
| "A" |
"B" |
"C" |
"D" |
| |
mm |
Inch |
mm |
Inch |
mm |
Inch |
| Ref |
±.203 |
±.008 |
±.254 |
±.010 |
±.254 |
±.010 |
|
| Right Angle Headers |
| "A" |
"B" |
"C" |
"D" |
"E" |
| mm |
Inch |
mm |
Inch |
mm |
Inch |
mm |
Inch |
mm |
Inch |
| ±.203 |
±.008 |
±.254 |
±.010 |
±.254 |
±.010 |
±.254 |
±.010 |
±.254 |
±.010 |
|
| Surface Mount Headers |
| "A" |
"B" |
"C" |
"D" |
"E" |
| mm |
Inch |
mm |
Inch |
mm |
Inch |
mm |
Inch |
mm |
Inch |
| ±.254 |
±.010 |
±.203 |
±.008 |
±.254 |
±.010 |
±.254 |
±.010 |
±.508 |
±.020 |
|
Sockets
Stamped Type
Insulator
Material - Glass filled thermoplastic, UL 94V-O Rated
Temp Range - -65o C to + 125o C - Hi Temp where indicated; -65oC to +240oC
Insulation Resistance - 5000 megohm @ 500 VDC
RoHS Compliant
Color - black
Contact -
Material - Phosphor Bronze
Current Rating - 1 amp continuous @ 100 VDC/Contact
Screw Machine Type -
Insulator
Material - Glass filled thermoplastic, UL 90 V-O rated
Temp Range - -65o to + 125oC
Insulation Resistance - 5000 MEG OHM @ 500 VDC
RoHS Compliant
Color - black
Contact -
Shell - Phosphor Bronze
Contact Clip - BeCu Spring
Current Rating - 1 amp continuous @ 100 VDC/Contact
TOLERANCES - unless otherwise noted on a specific part,
the following
tolerances apply to all parts.
| "A" |
"B" |
"C" |
"D" |
"E" |
| |
mm |
Inch |
mm |
Inch |
mm |
Inch |
mm |
Inch |
| Ref |
±.254 |
±.010 |
±.254 |
±.010 |
±.254 |
±.010 |
±.254 |
±.010 |
PLATING VALUES
| TLF |
= |
150u" (3.8u) pure bright tin over 50u" (1.3u) Ni |
| G |
= |
3- 5u" (.08 - .13u) gold over 50u" (1.3u) Ni |
| G1 |
= |
10u" (.25u) gold over 50u" (1.3u) Ni |
| G130 |
= |
30u" (.76u) gold over 50u" (1.3u) Ni |
| G2LF |
= |
10u" (.25u) gold over 50u" (1.3u) Ni at mating end - balance of pin 150u" (3.8u) pure bright tin over 50u" (1.3u) Ni |
| G230LF |
= |
30u" (.76u) gold over 50u" (1.3u) Ni at mating end- balance of pin 150u" (3.8u) pure bright tin over 50u" (1.3u) Ni (Consult Factory) |
| G30 |
= |
30u" (.76u) gold over 50u" (1.3u) Ni in mating zones- The balance of the pins is gold flash. |
| P1 |
= |
50u" (1.3u) Ni overall, followed by 30u" (.76u) Palladium/Ni overall, followed by 3u" (.08u) gold overall |
| P2 |
= |
50u" (1.3u) Ni overall, followed by 30u" (.76u) Paladium/Ni overall, followed by 3u" (.08u) gold on mating area, 150u" (3.8u) bright tin over 50u" (1.3u) Ni balance of pin |
Ordering
| All part numbers have a "BASE" number, to which must be added the number of circuits desired, and plating requirements. High temp plastic is available on most products, and where hi-temp is always supplied, it will be indicated on the catalog page. If hi-temp is desired, and it is not on the catalog page, call us for availability. |
 |
Contact Us for comments or suggestion on our site
|
